谁能帮帮忙!帮我翻译一下!
希望您能用到:
1 摇臂罩/袖套 2 摇臂罩/袖套螺纹 3 络筒机导丝
4 线程收紧水平 5 面板 6 臂导丝 7 张力调节盘 8 止动弹簧
9 臂导丝 10 针床针天心喷电针支撑杆 11针
12 压脚 13 针板 14 光泽机(打磨机)
15 针夹 16 底板 17 机械臂
18 常用缝纫表盘(转换钮)19 离合螺钉
20 平衡轮 21 拨禾轮、卷簧器 22 线柱
23 拉链表盘(杠杆) 24 压脚提升机
25 纱线剪刀 26 缝纫光开关 27 针位杠杆
28 压力调节器、压力控制器 29 滴油
30 弹力缝纫选择杠杆 31 覆盖凸轮
另附常用自动化设备词汇:
cutting equipment 裁衣工具
cutting out shears 裁衣剪
fabrics 布料
garment 衣服
general purpose scissors 多用途小剪刀
pinking shears 齿牙剪
non-fraying fabric 不散口布料
seam ripper 拆线刀
buttonholes 钮门
marking equipment 标记工具
tailor's chalk and pencil 画粉和画粉笔
tracing wheel and tracing paper 过线纸和裁衣辘
measuring equipment 量度工具
tape measure 软尺
measuring gauge 阔度量度器
straight ruler 直尺
drafting pattern 绘画纸样
sewing up equipment 缝合工具
needles 针
sharps 细孔长幼缝针
betweens 细孔短幼缝针
crewels 大孔幼缝针
thimble 顶针
protecting 保护
pins 大头针
pin cushion 针插
sewing threads 缝纫线
embroidery thread 刺绣线
treadle sewing machine 脚踏缝衣车
electric sewing machine 电动缝衣车 英语沙龙
spool pin 线柱
thread guide 引线器
tension regulator 线松紧调校器
take-up-lever 挑线杆
machine needle 车针
presser foot 压布靴
bobbin winder 绕底线器
hand / balance wheel 手轮
reverse stitch button 逆转调校器
stitch length regulator 针步长短调校器
slide plate
松开包装架上的螺丝,划开气垫膜,取出配件,移出包装架,配件箱中取出说明书,核对配件箱清单,丈量确定举升机安装位置,要求离墙3.5米。
Loosen the screw that package has put up , gash the air cushion film , take out an accessory , move out the package rack, the accessory takes out specifications in the box , checks the accessory box detailed list, the surveying ascertains an act rising machine assemble location , demand to be 3.5 meters away from a wall.
机器移到安装位置,竖起立柱,对照说明书所标注的尺寸,确认机器安装尺寸,拉出钢丝绳,将钢丝绳穿入滑体,预装钢丝绳锁紧螺母,调整钢丝绳嵌入滑轮槽。抬起滑体,确认滑体卡在第一档保险位置上,安装长油管,拧紧接头,盖好底板,装底板螺丝,再次对照说明书所标注的尺寸 确认机器安装位置,紧固底板螺丝,收紧钢丝绳,再次确认钢丝绳已收紧。安装保险齿条,先把齿块拧到离螺纹底部有2cm处,拆下开口销与弹簧,将保险齿条装入指定位置后 装上弹簧,插上开口销,确认立柱垂直度,并确认立柱在同一水平面,测出立柱并不在同一水平面时,轻轻地用铁锤侧向敲打至平行,先用冲击钻打孔,装入膨胀螺栓,再用榔头捶击膨胀钉,使膨胀螺栓在内部胀开,拧紧螺帽。
The machine moves to assembling location , to pricking up a column , contrast dimension marked by specifications , affirm the machine installation dimension , drag out a steel wire rope, a steel wire rope is pierced into smooth the body , is hold the steel wire rope jam nut with in advance, adjust a steel wire rope implanting the pulley slot. Raise smooth the body , affirm smooth the body getting stuck on the first archives insurance location , assemble the long oil pipe , screw connection tightly , finish building bottom board , hold bottom board screw with, once again, dimension marked by collation specifications affirms a machine assembling location , fastening bottom board screw , tightens up a steel wire rope, affirm a steel wire rope once again already having tightened up. Install the insurance rack , first the tooth piece is twisted arriving at be away from the thread bottom has 2 cms to get along, dismantling the cotter pin and spring down , install spring , having inserted a cotter pin , affirmed the column verticality after will be sure that the rack puts assigned address in, affirm and a column in the same horizontal plane , measure out a column when not depending on the same horizontal plane , use iron hammer side direction to beat till paralleling lightly , study punching intensively , put the swelling bolt in first with pounding, use hammer to thump the swelling nail again, Make the swelling bolt swell in the inside to come untied , screw a nut tightly.
安装托臂,插入销轴,调整保险齿条总成,将保险齿块与托臂齿咬合密切并拧紧螺丝,安装托盘总成,先将接套安装与托盘下方,再将托盘安装在托臂上。
Assemble the assembly supporting an arm , axis pin being thrust into , adjusting the insurance rack, will be sure that the tooth piece and support arm tooth holding-on close and tighten up a screw , assemble the pallet assembly, will receive cover installation and a pallet be assembled again on pallet down part, on supporting an arm first.
打开液压站包装,安装液压站,紧固固定板的螺丝,连接液压站到油缸处的短油管,先徒手安装油管接头,再用扳手拧紧,加注8到10升46或32号抗磨液压油,按电路图连接液压站电源线,确认通电,按动下降手柄,两立柱内同时发出“咔咔”声,确认保险正常,按上升按钮使举升机上升3到5厘米 离开保险档位,拉动保险拉绳,打开举升机两立柱内保险,按下降手柄 将举升机托臂下降至最低位置,上车调试,将车开入举升机内,将举升机托臂上的托盘支撑到汽车底盘的指定位置,按上升按钮将将托臂上升到离地30厘米处,检查举升机托臂上的托盘是否支撑到汽车底盘的支撑位置,按车头及车尾,确认车辆已在支撑点上稳固,按上升按钮上升到最顶端,按下降手柄,使保险卡在保险档位上,按上升按钮,举升机保险离开保险档位,拉动保险拉绳,按下降手柄,将举升机托臂放到最低位置,移开举升机托臂,将汽车开出举升机,调试完毕。在立柱内侧槽内抹上黄油,擦拭举升机,清扫地面,安装调试举升机完毕。
Open hydraulic pressure station package , assemble the hydraulic pressure station, the fastening fixes unnatural screw , the station linking hydraulic pressure arrives at the short oil pipe that the oil jar gets along , the first bare-handed installation oil pipe connects , uses spanner to screw tightly again, inject additional 8 arriving at 10 litres of 46 or 32 number antifriction hydraulic pressure oil , link hydraulic pressure station mains lead , affirm the handle electrifying , coming down according to moving according to the circuit diagram, that the inner sends out two columns at the same time "clicking to click " to affirm insurance is regular, The button makes an act rise according to rising machine rise by 3 leaving the insurance archives place to 5 centimetres, play move insurance pull wire, open an act rising machine two column inner are sure that the handle will choose according to coming down rising, machine ask an arm to fall to the lowest point down lathing a debugging on location, vehicle is fired entering an act rising within machine, will choose rising machine ask the upper pallet of arm to prop up the assigned address to automobile chassis, the button asks an arm to rise to being 30 centimetres of place away from a field barely according to rising, The machine examining that the act rises supports upper if pallet prop up propping up to automobile chassis of arm location, according to the end of headstock and vehicle , affirm a vehicle already on the center of resistance firm, the button rises according to rising arriving at that the top, pushes down the go down handle most, makes an insurance card push down the go up button on insurance archives place, the act rises machine be sure leaving the insurance archives place , play according to go down handle moving insurance pull wire,will choose rising machine ask an arm to readjust oneself to a certain extent to minimum location , move away an act rising machine support an arm, An automobile is fired out choosing rising machine , the debugging are finished. Having rubbed butter , cleaned an act rising within column inner side slot machine , the cleaning floor, assemble the debugging act rising machine be finished.
希望能帮到你
规格为4mm的内六角扳手
Fork spanner
叉形扳手
10mm ring spanner : slightly offset or straight
规格为10mm的梅花扳手:可稍笔偏斜或保持笔直
10mm combination wrench (HK. order NO 52044-310)
规格为10mm的组合扳手(香港订单号 52044-310)
side cutter
偏铣刀
square spanner
方头扳手
fork spanner spanner opening 13
叉形扳手 扳手口距 13
Dial guage(0.001)
千分表
Dial guage(0.01)
百分表
Magic stand with measuring arm extension
带加长测量臂的魅力底座
stone block
石块
Align stone
对准石?
lever test indicator(puppitast)
杠杆式测微仪指示器
plug gauge 40mm diameter
圆柱塞规 直径40mm
200mm long block gauge 200mm
长为200mm的块规
ROD
检验棒
spirit level
酒精水平仪
Precision spirit level (small)
高精度水平仪(小号)
large digital slide gauge
大号数字卡尺
large slide gauge
大号卡尺
Depth gauge
测深仪
half-inch ratchet spanner +250mm extension +10mm nut
规格为半英寸的棘轮扳手 + 250mm加长杆 + 10mm的头
克丝钳子 wire cutting pliers
尖嘴钳nipper pliers
斜嘴钳giagonal cutting nippers
平口改锥 flat screwdriver
十字改锥 cross screwdriver
活动扳手 adjustable wrench
开口扳手open spanner
公制内六方扳手 allen wrench (metric system)
英制内六方扳手 allen wrench (English system)
万用表 universal meter
电烙铁 electric iron
胶布(带)adhesive tape
Abnormal knocking 异响
Abnormal motion 异常运动
Abrasion 磨蚀,磨损,研磨
Abrasion resistance 耐磨性、抗磨性
Abrasion resisting properties 耐磨性
Abrasion test 磨损试验
Abrasive 磨料
Abrasive cloth 砂布
Abrasive paper 砂纸
Abrasive powder 研磨粉
Abrasive resistance 耐磨性
Abrasive stick 油石、磨条
Abrasive stone 油石
Abrasive wear 磨损,磨蚀
Abrasive wheel 磨轮,砂轮
Aerator 抛丸清理机
Abscissa 横坐标
Absolute altitude 绝对高度
Absolute humidity 绝对湿度
Absolute motion 绝对运动
Absolute pressure 绝对压力
Absolute temperature 绝对温度
Absolute unit 绝对单位
Absolute value 绝对值
Absolute velocity 绝对速度
Absorb 吸收
Absorbed power 吸收功率
Absorbed torque (测功器)吸收扭矩
Absorption 吸收
Ace 加速器;加速踏板;催化剂
Accelerated ageing 加速老化
Accelerated life test 加速寿命试验
Accelerated load test 加速负荷试验
Accelerating ability 加速能力
Accelerating jet 加速喷嘴
Accelerating pump加速泵
Accelerating resistance 加速阻力
Accelerating winding加速线圈
Acceleration 加速度
Acceleration lane 加速车行道
Acceleration limiter 加速限制器
Acceleration meter加速度计
Acceleration of vibration 振动加速度
Acceleration performance 加速性
Acceleration pickup加速度传感器
Acceleration spectrum 加速度谱
Acceleration vector of center of mass质心加速度矢量
Accelerator (美)油门(踏板)
Accelerator jet 加速喷嘴(量孔)
Accelerator nozzle 加速喷嘴
Accelerator pedal 加速踏板
Accelerator pump加速泵
Accelerator vacuum switch加速踏板真空开关
Accel pedal 加速踏板,油门踏板
Acceptance验收
Acceptance test 验收试验
Accessibility 可接近性
Accessories附件
Accessory device 附属装置
Accident 意外,事故
Accommodation 适应;调节作用;居住设备
Accordion 可折叠的;折叠屏风
Accordion coil 折形线圈
Accordion door 折叠门
Accordion partition 折叠隔板
Accumulation wear average 累计平均磨耗
Accumulator 蓄能器,蓄电池
Accuracy 精度
Accuracy class 精度等级
Accuracy control 精确控制
Accuracy of manufacture 制造精度
Accuracy of measurement 测量精度
Accuracy of positioning 定位精度
Accuracy of reading 读数精度
Accuracy of repetition 复制精度;重复精度
Accuracy of thread 螺纹精度
Aceton 丙酮
Acetylene 乙炔
AC generator 交流发电机
Acid 酸
Acid-proof alloy 耐酸合金
Acid-proof pipe 耐酸管
Acid tanker 酸罐车
Acid vapour 酸罐汽
Acme thread 梯形螺纹,爱克姆螺纹
Acoustic absorption 吸音
Acoustic insulation 隔音
Acoustic panel 吸声板
Acoustimeter 声级计,噪声计
Acquisition 探测;搜索
Acquisition of signal 信号采集
Acre 英亩
Acryl 丙烯酸树脂
Active braking distance 有效制动距离
Active braking time 有效制动时间
Active suspension 主动悬架[挂]
Actuating arm 驱动臂
Actuating cam 致动凸轮
Actuating line 促动管路
Actuating motor 伺服电动机
Actuating time 促动时间
Actuator 执行机构,操作机构
Actuator track 滑轨
Adapter 接头;适配器
Adapter plate 安装板,固定板
Adapter ring 接合环
Adapter sleeve 紧固套,连接套
Addendum 齿顶高,齿顶
Addendum circle 齿顶圆
Addendum face 齿顶面
Additional seat 附加座椅
Additional temperature error 温度附加误差
Additional wheel drive control 附加驱动车轮的操纵件
Adhesion 附着;附着力;
Adhesion coefficient 附着系数
Adhesive 黏合剂
Adiabatic 绝热的
Adiabatic compression 绝热压缩
Adjust 调整,调节,校正
Adjustable 可调节的
Adjustable brush 可调电刷
Adjustable fork spanner 可调*形扳手
Adjustable pedal 可调踏板
Adjustable reamer 可调铰刀
Adjustable seat 可调节的座椅
Adjustable shutter 可调百叶窗
Adjustable spanner 活动扳手
Adjustable stop screw 活动止动螺钉
Adjustable wheel 可调式车轮
Adjustable wrench 可调扳手,活扳手
Adjusting 调整用的
Adjusting cam 调整凸轮
Adjusting hand wheel 调整手轮
Adjusting lever 调整杆
Adjusting nut 调整螺母
Adjusting shim 调整垫片
Adjusting spring 调整弹簧
Adjusting washer 调整垫圈
Adjustment 调整,调节
Admission cam 进气凸轮
Admission cam shaft 进气凸轮轴
Admittance 导纳;加工余量;通道
Advanced ignition 提前点火
Advancer (点火)提前装置
Advertising car 广告汽车
Aerial 天线
Aerial pollution 大气污染
Aerodynamic angle of attack 气动迎角
Aerodynamic body 流线形车身
Aerodynamic drag 空气动力阻力
Aerodynamic force 气动力
Aerodynamic retarder 空气动力缓速装置[器]
Aerodynamics 空气动力学
Aero-stabilizer 气动力稳定装置
Affinity 亲和力,亲和性
After-burning 补燃,后燃,复燃
After fire 消音器内爆炸;(点火开关切断后)自燃现象
After-running 发动机惯性运转
Age 年龄;老化;使用期限
Age hardening 时效硬化
Age resister 老化防止剂
Aging 老化;时效
Aiming of headlamp 前照灯对准
Air bag (撞车保护用)气袋
Air bleeding 放气
Air bleed screw 放气螺钉
Air bleed valve 空气溢流阀
Air booster 气压助力器
Air brake 空压制动
Air brake actuator 气压制动执行器
Air brake antifreeze tank 气压制动防冻液罐
Air brake chamber 气压制动室
Air brake equalizer 气压制动补偿器
Air brake governor 气压制动调节器
Air brake hose dummy coupling气压制动软件管(未连接时的)堵头
Air brake reservoir pressure indicator 贮气简压力表
Air brake valve 气制动阀
Air braking system 气制动系
Air bypass 空气旁路
Air car 气垫汽车
Air chamber type combustion chamber 空气室式燃烧室
Air check valve (空气)单向阀
Air choke 阻风门
Air cleaner 空气滤清器
Air cleaner bracket 空气滤清器支架
Air cleaner cartridge 空气滤清器滤芯
Air cleaner casing 空气滤清器外壳
Air compression ga(u)ge 空气压力表
Air compressor 空气压缩机
Air conditioner 空调装置
Air conditioning 空气调节
Air conditioning control 空调装置操纵件
Air cooler 空气冷却器
Air cooling engine 风冷式发动机
Aircraft shunt bus 机场联运客车
Aircraft tire 航空轮胎
Air damper 空气缓冲器
Air dam skirt 气堰裙板,前阻风板
Air deflector 导流板
Air dryer 空气干燥器
Air duct 通气道
Air exhaust filter 排气滤清器
Air feed pipe 送气管
Air filter 空气滤清器
Air filter tell-tale 空气滤清器警报灯
Air flow meter 空气流量计
Air fuel ratio 空气燃料比
Air ga(u)ge 气压表
Air gate 气流调节门
Air governor 空气调速器
Air gun 空气喷枪
Air hammer 空气锤
Air horn 气喇叭
Air hose 空气软管
Air injection 空气喷射
Air inlet 进气口
Air inlet port 进气孔
Air insulation 空气绝缘
Air intake 进气,吸气
Air intake filter 进气滤清器
Air leak 漏气
Airless injection 无气喷射
Air line lubricator 气压供油中央润滑系统
Air lock 气阻,气障
Air nozzle 喷气嘴
Air outlet 出气口
Air over hydraulic booster 气顶油助力器
Air pipe 通气管
Air pollution 大气污染
Air pressure 气压
Air pressure relay valve 气压继动阀
Air quench hardening glass 风冷钢化玻璃
Air regulating valve 空气调节阀
Air relief cock 放气旋塞,放气开关
Air required for combustion 燃烧必要空气量
Air resistance 空气阻力
Air speed governor 空气式调速器
Air spoiler 空气阻流板
Air sprayer 空气喷雾器
Air spring 空气弹簧
Air storage reservoir 储气罐
Air strangler 阻风门
Air strangler spindle 阻风门轴
Air suction pipe 进气管,吸气管
Air suspension 空气悬架[挂]
Air tank 储气罐
Air throttle valve 空气节气门
Air-tight 气密的
Air-tight chamber 气密室
Air-tightness 气密性
Air tube (轮胎)内胎
Air valve 气阀,气门
Air vent 通气孔
Air wiper 压缩空气式刮水器
Aisle 通道
Alarm device 报警装置
Alarm pressure 报警压力
Alcohol 酒精
Alcohol-blended fuel 掺酒精的燃料
Align 调整,校直,定中心
Aligner 定位器,校直器,调整器;前轮定位仪
Aligning(torque) stiffness 回正(力矩)刚度
Aligning (torque) stiffness coefficient 回正(力矩)刚度系数
Aligning torque 回正力矩
Aligning torque coefficient 回正力矩系数
Alignment 定位,对中心
Alignment check 定位检查
Alkali 碱性,强碱
Alkali degreater 碱脱油剂
Alkali detergent 碱去垢剂
Alkohol 乙醇,酒精
All dog clutch transmission 全齿套变速器
Allen wrench 内六角扳手
Alligator bonnet 鳄口形发动机罩
Alligator shears 鳄式剪床
Allowable cargo load 容许载货量
Allowable deflection 容许挠度[变位]
Allowable dimension variation 允许尺寸偏差
All-purpose adhesive 万能胶
All-sponge rubber upholstery 全海绵橡胶汽车内饰
All-steel body 全钢车身
All synchromesh transmission 全同步器式变速器
All-weather body 全天候车身
All wheel drive 全轮驱动
Alternating current 交流
Alternator 交流发电机
Altimeter 测高仪
Altitude compensating 海拔补偿
Altitude control device (化油器)适应高度控制油量的装置
Aluminium alloy 铝合金
Aluminium soap grease 铝基润滑脂
Amber light 琥珀色灯光
Ammeter 电流表,安培表
Ammonia gas 氨(气)
Ampere 安(培)
Amplitude 振幅,幅度
Anchor 支承销
Anchor plate 支承板,支承块
Angle bar 角铁
Angle ga(u)ge 量角器,角度计
Angle iron 角铁
Angle of advance 提前角
Angle of cone 锥角
Angle of delay 滞后角
Angle of friction 磨擦角
Angle of lead 超前角
Angle of lock 锁角
Angle of repose 静止角
Angle of retarded closing 延迟关闭角
Angle of roll 侧倾角
Angle of steering lock 最大转向角
Angle of twist 扭转角
Angular acceleration 角加速度
Angular clearance 拔模斜度
Angularity of connecting rod 连杆倾斜角
Angular moment 转矩
Angular momentum 角动量
Angular wheel 圆锥齿轮
Animal oil 动物油
Anneal 退火
Annealing 退火(作用)
Annual average daily traffic 年平均日交通量
Annual survey 年度检验
Annular seat 环形座
Annular spring 环形弹簧
Annulus (行星齿轮系的)内齿环
Ante-chamber 预燃室
Antenna 天线
Antibacklash spring 消隙弹簧
Anti-blocking brake 防抱死制动器
Anticorrosion 抗蚀性
Anticorrosive oil 防锈油
Antidazzle screen 遮阳板
Antidazzle switch 变光开关
Antidetonant 抗爆剂
Anti-freezer 防冻器;防冻液
Antifreezing solution 防冻液
Antifriction alloy 耐磨合金
Antifriction bearing 滚动轴承
Antiknock gasoline 抗爆汽油
Anti-knock nature 抗爆性
Antiknock value 抗爆值
Anti-lock brake sensor防抱死制动传感器
Anti-lock brake system 防抱死制动系统
Antioxidant 抗氧燃料
Anti-rattle spring 防震弹簧
Antiroll bar 防侧摆杆
Antirust grease 防锈脂
Antiscale agent 防垢剂
Antiskid tread 防滑轮胎纹
Antiskid tyre 防滑轮胎
Anti-spatter compound 防溅剂
Anti-squat 抗后坐
Antiwear hydraulic oil搞磨液压油
Aperture 孔,口,缝隙,孔径
Apex 反射点;顶点,顶部;填充胶条
Apex seal (转子)顶端密封垫片
Appearance 外观,外形
Appearance test 外观检验
Application force 作用力
Approach angle 接近角
Apron 挡板;拖板箱
Apron control 拖板控制
Aquaplaning 水层效应;漂滑现象
Aqueous ingredients 含水量
Arbo(u)r 轴,心轴;芯骨
Arbo(u)r press 手扳压床,矫正机
Arc 电弧
Arc welding 电弧焊
Areometer 液体比重计
Arm 臂
Armature 电枢
Armature changed type starter 电枢移动式起动机
Armature core 电枢铁芯
Armature reaction 电枢反应
Armature shaft 电枢轴
Armature spindle 电枢轴
Armature terminal 电枢输出端接线柱
Armature tester 电枢测试装置
Armature winding 电枢绕组
Arm of wheel 轮辐
Armored motor car 装甲车
Arm rest 肘*
Arm shaft 臂轴
Arm support 肘*
Arm winker 臂式方向指示器
Arrangement of camshaft 凸轮轴装置
Articulated bus 铰接客车
Articulated cross shaft 铰接式横轴
Articulated jack 铰接式千斤顶
Articulated joint 关节接合
Articulated sixwheeler 铰接式六轮汽车
Articulated utility carrier 铰接式通用载运车
Articulation piece 铰接件
Artificial gasoline 人造汽油
Asbest(os) 石棉
Asbestos-copper gasket 铜石棉衬垫
Ash content 灰分,灰分量
Ash tray 烟灰盘
Aspect concrete pavement 沥青混凝土路面
Asphalt distribution truck沥青洒布车
Assembly 装配,总成
Assembly belt 装配传送带
Assembly conveyor 装配传送线
Assembly drawing 装配图
Assembly jig 装配夹具
Assembly part 装配零件
Assembly shop 装配车间
Assist grip (副驾驶)扶手
Asymmetrical beam 非对称光
Asymmetric low beam headlamp 不对称近光束前照灯
Asymptotic stability 渐近稳定性
Atmospheric electricity 天电,大气电
Atmospheric moisture 大气温度
Atmospheric pressure compensating 气压补偿
Atomising installation 喷雾装置
Atomization 喷雾
Atomizer 喷雾器
Atomizer orifice 喷雾器喷嘴
Atomizing chamber 雾化室
Atomizing disc 雾化盘
Attachment face 安装面
Attendance 保养
Audible warning (horn)control 音响警告(喇叭)操纵件
Austenite 奥氏体
Austenite steel 奥氏体钢
Authorized maximum towed mass 允许最大拖挂质量
Autobahn(德) 高速公路
Autobicycle 摩托车,机器脚踏车
Auto-body 汽车车身
Autocorrelation 自相关
Autocorrelation coefficient 自相关系数
Autocorrelation function 自相关函数
Autodrive 自动定速驾驶器
Autolevelizer 自动水平调节器
Autolift 举车器
Automatic 自动的
Automatic advance of ignition 自动提前点火
Automatically advanced distributor 自动提前分电器
Automatically timed magneto 自动正时磁电机
Automatic antenna control 自动天线操纵杆
Automatic braking system 自动制动系
Automatic circuit breaker 自动断路器
Automatic circulation 自动循环
Automatic clutch 自动离合器
Automatic control 自动操纵
Automatic door closing device 自动关门装置
Automatic door tell-tale 显示门未闭好的警报灯
Automatic engine stop tell-tale 发动机自动停机警报灯
Automatic gear change 自动换档
Automatic gearbox indicator 变速器自动指示器
Bead wire core 胎缘钢丝芯
Beam 梁,光束
Beam adjusting disk plate 调光座盘
Beam center 光束中心,亮区
Beam of light (前照灯)光束
Bearing 轴承
Bearing bush 轴承套
Bearing cap 轴承盖
Bearing face 支承面
Bearing friction 轴承摩擦
Bearing lining machine 轴承浇铸机
Bearing metal 轴承合金,轴瓦
Bearing pressure 支承压力,轴承压力
Bearing puller 轴承拆卸器
Bearing retainer 轴承保持架
Bearing spacer 轴承隔圈
Bearing steel 轴承钢
Bell crank 曲柄
Bell frame 钟形架
Bell housing 钟形外壳
Bellows 风箱波纹管
Bellows thermostat 波纹管式节温器
Bellows type pneumatic suspension 风箱式空气悬架
Bellow type container 波纹管式容器
Belt 皮带;(轮胎)带束层
Belt conveyor 传送带
Belt drive 皮带传动
Belt drive fan 皮带驱动风扇
Belt fastener 传动带接头
Belt pulley 皮带轮
Belt stretching device 传动带拉紧装置
Belt tension 传动带张力
Bench seat 长凳车座
Bench test 台架试验
Bending 弯曲
Bending moment 弯矩
Bending strength 抗弯强度
Bending tester 弯曲试验机
Bendix-type starter 惯性接合式起动机
Bend of road 道路弯度
Bend of spring 弹簧拱度
Bent socket wrench 弯形套简扳手
Bevel gear 锥齿轮
Bevel gear lapping machine 锥齿轮研磨机
Bevel gear wheel 大锥齿轮
Bias 斜交,斜角
Bias belted tire 带束斜交轮胎
Bias fabric 斜经帘布
Bias ratio 差速器锁止系数
Bicycle 自行车
Bicycle tire 自行车轮胎
Big end (连杆)大头
Big end bearing 大端轴承
Bimetal 双金属,复合钢材
Bimetal fuel ga(u)ge 双金属油量计
Bimetallic oil pressure indicator 双金属式油压指示器
Bimetallic oil pressure sensor 双金属式油压传感器
Bimetal strip 双金属带
Bimetal thermostat 双金属式节温器
Binary alloy 二元合金
Binary fuel 二元燃料
Binding (车身)压条
Binding end cap 压条封盖